VERIFIED
When a Bosch dishwasher shows E6101, the source record points to drain-pump fault or blockage. Use symptoms and model-specific checks to decide when service is needed.
A Bosch dishwasher showing E6101 is reporting a condition associated with drain-pump fault or blockage. Use the code as a starting point, then pair it with the full model/E-Nr and the way the appliance behaves.
Treat the code as evidence, not a complete diagnosis. Record what the appliance does, complete only the safe checks that fit the exact model, and arrange testing if the warning remains active or comes back.
At a glance
- Code: E6101
- Appliance: Bosch Dishwasher
- Verified meaning: drain-pump fault or blockage
- Diagnostic direction: the drain path or water-removal system
- Service area context: San Francisco; confirm coverage by ZIP code
How to read this warning
The technical anchor for E6101 is drain-pump fault or blockage. That description should remain unchanged when the page is imported. What can vary is the hardware behind the condition, so the model/E-Nr and the observed behavior are necessary context.
For this reason, E6101 should be used to narrow the troubleshooting path toward the drain path or water-removal system, not as automatic proof that one specific component has failed.
Symptoms that add diagnostic context
Before changing settings or cycling power, note what the appliance is doing. Useful observations include:
- Standing standing water can remain after the cycle.
- The pump can hum without clearing the tub.
- Draining might stop partway through.
- The code can appear repeatedly at the drain stage.
Where diagnosis may need to look
Based on the source record, diagnosis may need to consider the following possibilities without assuming any one of them is confirmed:
- Drain-pump blockage.
- Drain-pump mechanical or electrical fault.
- Wiring or control fault in the drain-pump path.
Safe checks before service
- Turn power off before any owner-manual pump-area check.
- Look over the user-accessible filter and pump-cover area only where the manual permits it.
- Verify the visible drain hose for kinks.
- Avoid reach into a pump area with power connected.
These steps are meant to gather useful information without exposing live wiring, bypassing an interlock, defeating a leak-protection device, or opening a system the owner documentation does not designate for user access.
Safety stop conditions
Stop for active leaking or water near electrical components.
What service needs to determine
If the accessible path is clear but the pump still cannot evacuate water, internal pump and electrical diagnosis is the next step. When requesting service, include the complete Bosch model/E-Nr. Similar-looking dishwashers can use different controls, pumps, drying systems, and diagnostic logic.
A useful service request includes the exact display, what the appliance was doing immediately before the warning, and which external checks were already completed.
Before parts or service are selected
Use the complete Bosch model/E-Nr when matching E6101 to technical documentation. Similar-looking products can use different sensors, controls, pumps, motors, or diagnostic logic.
FAQ
For the source record used here, E6101 is associated with drain-pump fault or blockage. The complete model/E-Nr still matters because Bosch can use different hardware and diagnostic logic across product families.
Do not continue if the warning is accompanied by the stop conditions listed above. Water near electrical parts, leaking, smoke, a burning odor, sparking, or repeated breaker trips are reasons to leave the appliance off and arrange service.
Where the Bosch documentation for the exact model allows a normal power reset, use it once after recording the code. A returning warning means the underlying condition still needs attention; repeated resets are not a repair.
Not necessarily. An error code narrows the detected condition or system. The model number, symptoms, and model-specific testing are still needed before selecting a component.
Have the full Bosch model/E-Nr, the exact E6101 display, the cycle stage or operating state when it appears, the visible symptoms, and the safe checks already completed.
Bosch service in the San Francisco area
Does Bosch dishwasher code E6101 keep returning?
If E6101 remains active or returns, request Bosch dishwasher diagnosis for the San Francisco service area. Include the complete model/E-Nr, the exact code, a short symptom description, and your ZIP code so service coverage can be confirmed.
service notice: This site represents an appliance repair service and is not affiliated with or endorsed by Bosch.
Technical source: https://www.bosch-home.com/us/owner-support/error-codes/dishwashers
Model compatibility: Bosch reuses codes across series and model years, so Bosch Dishwasher E6101 Error Code may mean something different on another appliance or generation. Confirm this against your model’s documentation and record your full model number before acting.