VERIFIED
Bosch washing machine E1000 / E10-00 is associated with intelligent-dosing pump is blocked on applicable models. Review the operating signs and safe external checks before deciding on the next step.
When E1000 / E10-00 appears on a Bosch washing machine, the control has registered intelligent-dosing pump is blocked on applicable models. That points the diagnostic process toward the door, latch, or locking system, but the display alone is not enough to choose a replacement part.
The guidance below stays at the owner-safe level: observe the symptom, check only accessible items supported by the model documentation, and stop before opening protected electrical, water, gas, or mechanical systems.
At a glance
- Code: E1000 / E10-00
- Appliance: Bosch Washing Machine
- Verified meaning: intelligent-dosing pump is blocked on applicable models
- Diagnostic direction: the door, latch, or locking system
- Service area context: San Francisco; confirm coverage by ZIP code
What the code is pointing to
The technical anchor for E1000 / E10-00 is intelligent-dosing pump is blocked on applicable models. That description should remain unchanged when the page is imported. What can vary is the hardware behind the condition, so the model/E-Nr and the observed behavior are necessary context.
For this reason, E1000 / E10-00 should be used to narrow the troubleshooting path toward the door, latch, or locking system, not as automatic proof that one specific component has failed.
Operating signs to record
Before changing settings or cycling power, note what the appliance is doing. Useful observations include:
- The appliance might not start.
- A cycle can end prematurely unexpectedly.
- The door can remain locked or fail to lock.
- The control might not recognize the expected door position.
Possible causes from the source record
Based on the source record, diagnosis may need to consider the following possibilities without assuming any one of them is confirmed:
- The door not reaching its expected position.
- A damaged latch, hook, or lock mechanism.
- A door sensor or switch fault.
- Wiring or electronic control failure in the interlock path.
First checks to make safely
- Confirm clothing, cookware, or another object is not preventing normal closure.
- Look over the visible latch area for obvious debris or physical damage.
- Avoid force a locked door and do not bypass the interlock.
These steps are meant to gather useful information without exposing live wiring, bypassing an interlock, defeating a leak-protection device, or opening a system the owner documentation does not designate for user access.
When to stop using the appliance
Do not continue operating an appliance with a door that cannot latch securely or with a defeated safety interlock.
If the code comes back
A returning door code with normal external alignment requires testing of the lock/switch, wiring, and model-specific control path. A displayed code is evidence, not a parts order. The next step is to confirm the reported system against the model and the symptoms present during operation.
A useful service request includes the exact display, what the appliance was doing immediately before the warning, and which external checks were already completed.
Use the complete Bosch E-Nr
Use the exact Bosch model number when booking. It is the safest way to connect E1000 / E10-00 with the correct technical documentation and related parts.
FAQ
For the source record used here, E1000 / E10-00 is associated with intelligent-dosing pump is blocked on applicable models. The complete model/E-Nr still matters because Bosch can use different hardware and diagnostic logic across product families.
Do not continue if the warning is accompanied by the stop conditions listed above. Water near electrical parts, leaking, smoke, a burning odor, sparking, or repeated breaker trips are reasons to leave the appliance off and arrange service.
Where the Bosch documentation for the exact model allows a normal power reset, use it once after recording the code. A returning warning means the underlying condition still needs attention; repeated resets are not a repair.
Not necessarily. An error code narrows the detected condition or system. The model number, symptoms, and model-specific testing are still needed before selecting a component.
Have the full Bosch model/E-Nr, the exact E1000 / E10-00 display, the cycle stage or operating state when it appears, the visible symptoms, and the safe checks already completed.
Bosch service in the San Francisco area
Still seeing E1000 / E10-00 on your Bosch washing machine?
If E1000 / E10-00 remains active or returns, request Bosch washing machine diagnosis for the San Francisco service area. Include the complete model/E-Nr, the exact code, a short symptom description, and your ZIP code so service coverage can be confirmed.
service notice: This site represents an appliance repair service and is not affiliated with or endorsed by Bosch.
Technical source: https://www.bosch-home.com/ne/service/get-support/get_support_st4/get_support_st4_washing_machines_static_page
Model compatibility: Bosch reuses codes across series and model years, so E10 may mean something different on another appliance or generation. Confirm this against your model’s documentation and record your full model number before acting.